2022 mazda cx-5 headlight bulb

Halogen Type

Headlight LO bulb

1. Disconnect the negative battery cable..

2. Disconnect the connector.

3. Rotate the headlight LO bulb in the direction of the arrow (1) shown in the figure to remove it in the direction of the arrow (2) shown in the figure.

CAUTION:

• A halogen bulb generates extremely high heat when it is illuminated. If the surface of the bulb is soiled, excessive heat will build up and the life of the bulb will be shortened. When replacing the bulb, hold the metal flange, not the glass.

4. Install in the reverse order of removal.

Headlight HI bulb

1. Disconnect the negative battery cable..

2. Disconnect the connector.

3. Rotate the headlight HI bulb in the direction of the arrow (1) shown in the figure and remove it in the direction of the arrow (2) shown in the figure.

CAUTION:

• A halogen bulb generates extremely high heat when it is illuminated. If the surface of the bulb is soiled, excessive heat will build up and the life of the bulb will be shortened. When replacing the bulb, hold the metal flange, not the glass.

4. Install in the reverse order of removal.

Discharge Type

WARNING:

• Incorrect servicing of the discharge headlights could result in electrical shock. Before servicing the discharge headlights, always refer to the service warnings..

Headlight HI/LO bulb (LH)

1. Disconnect the negative battery cable..

2. Remove the air cleaner cover..

3. Remove the relay and fuse block upper cover..

4. Remove the nut and screw.

5. Insert a tape-wrapped flathead screwdriver into the service hole in the position shown in the figure.

6. While pressing the pin tab in the direction of the arrow (1) shown in the figure using a flathead screwdriver, pull the pin in the direction of the arrow (2) shown in the figure to detach the pin tab and engine mount.

7. Pull out the relay and fuse block from the stud bolt and set it aside as shown in the figure.

8. Rotate the cover in the direction of the arrow (3) shown in the figure and remove it from the front combination light in the direction of the arrow (4) shown in the figure.

9. Rotate the igniter in the direction of the arrow (5) shown in the figure and remove it from the front combination light in the direction of the arrow (6) shown in the figure.

10. Move section A of the bulb retaining wire in the direction of the arrow (7) shown in the figure, pull it in the direction of the arrow (8) shown in the figure, and detach the bulb retaining wire and hook.

11. Remove the headlight HI/LO bulb.

CAUTION:

• The discharge headlight bulb generates extremely high heat when it is illuminated. If the surface of the bulb is soiled, excessive heat will build up and the life of the bulb will be shortened. When replacing the bulb, hold the metal flange, not the glass.

12. Install in the reverse order of removal.

Headlight HI/LO bulb (RH)

1. Disconnect the negative battery cable..

2. Remove the washer tank bracket..

3. Rotate the cover in the direction of the arrow (1) shown in the figure and remove it from the front combination light in the direction of the arrow (2) shown in the figure.

4. Rotate the igniter in the direction of the arrow (3) shown in the figure and remove it from the front combination light in the direction of the arrow (4) shown in the figure.

5. Move section A of the bulb retaining wire in the direction of the arrow (5) shown in the figure, pull it in the direction of the arrow (6) shown in the figure, and detach the bulb retaining wire and hook.

6. Remove the headlight HI/LO bulb.

CAUTION:

• The discharge headlight bulb generates extremely high heat when it is illuminated. If the surface of the bulb is soiled, excessive heat will build up and the life of the bulb will be shortened. When replacing the bulb, hold the metal flange, not the glass.

7. Install in the reverse order of removal.

Headlight Auto Leveling System Initialization

NOTE: The AFS control module records the vehicle height while it is unoccupied by performing the headlight auto leveling system initial setting. Perform headlight auto leveling syst ...

Headlight High Beam Indicator Light

Purpose Notifies the user that the headlights (HI) are illuminated. Function Illuminates when the headlight (HI) or parking illumination conditions are met. Construction ...

Other materials:

Airflow Mode Actuator Inspection [Full Auto Air Conditioner]
CAUTION: If the lever position exceeds the operation range shown in the figure, the circuit in the actuator could be damaged. Always perform an actuator operation inspection with the lever movement within the range shown in the figure. 1. Connect battery positive voltage to airfl ...

Oil Pump Removal/Installation [Skyactiv G 2.0]
WARNING: Hot engines and engine oil can cause severe burns. Turn off the engine and wait until it and the engine oil have cooled. A vehicle that is lifted but not securely supported on safety stands is dangerous. It can slip or fall, causing death or serious injury. Never work ...

Engine Oil Control
Outline The PCM reduces the oil pump load applied to the engine by controlling the appropriate engine hydraulic pressure according to the engine operation conditions. The engine hydraulic pressure switches in two steps. When hydraulic pressure is not needed, the oil pump dischar ...

© 2016-2022 Copyright www.mcx5.org

Does Mazda CX

Does the 2022 CX

Does the 2022 Mazda CX

Is Mazda redesigning the CX